Endpoint Route Table

Available in VPC

Endpoint Route Table allows you to set ingress routing traffic for traffic incoming to the endpoint. The detailed features of the Endpoint Route Table are as follows:

• Only the endpoints created in the transit VPS can be applied.
• Applicable endpoints are Internet Gateway (IGW), Virtual Gateway (VGW), and Transit VPC Connect.

View Endpoint Route Table list

In the list of created and operating Endpoint Route Tables, you can view information by Endpoint Route Table. To check the information, follow these steps:

1. From within the VPC environment on the NAVER Cloud Platform console, click Services> Networking> VPC in order.
2. Click the Endpoint Route Table menu.
3. When the list of created route tables appears, view the summarized information, or click the route table to see details.
   • Route table name: name of the Endpoint Route Table
   • Route table ID: ID value of the Endpoint Route Table
   • VPC name: name of the VPC using the Endpoint Route Table
   • Status: status of the Endpoint Route Table
     • Operating: status in which the creation of the route table has been completed with the information you entered, and the route table is available for use.
     • Configuring: status in which the route table is being configured with the information you entered
   • Related endpoint type: type of endpoints using the Endpoint Route Table
   • [Set related subnet] tab: set the endpoints where the Endpoint Route Table is used
   • [Set routes] tab: list of routing rules included in the Endpoint Route Table
   • Note: memo related to the Endpoint Route Table. You can edit it by clicking the [Edit] button

Create Endpoint Route Table

To create an Endpoint Route Table, follow these steps:

1. From within the VPC environment on the NAVER Cloud Platform console, click Services> Networking> VPC in order.
2. Click the Endpoint Route Table menu.
3. Click the [Create Endpoint Route Table] button.
4. When the Create Endpoint Route Table popup window appears, enter the information for the route table to be created
   • Route table name: enter the name of the route table to create, in 3 to 30 characters using English letters, numbers, and hyphens (-).
   • VPC: select the transit VPC to use the Endpoint Route Table
   • Related endpoint type: select the type of the endpoint to use the Endpoint Route Table
5. Click the [Create] button.
6. Check the status of the created Endpoint Route Table from the list in the Endpoint Route Table page.
   • Operating: status in which the creation of the Endpoint Route Table has been completed with the information you entered, and the route table is available for use.
   • Configuring: status in which the route table is being configured with the information you entered
7. Set routing rules to include the Endpoint Route Table, and specify the endpoint to apply the rules to.
   • Routing rule setup guide
   • Related endpoint setup guide

Set routing rules

To add or delete routing rules to/from the created route table, follow these steps:

1. From within the VPC environment on the NAVER Cloud Platform console, click Services> Networking> VPC in order.
2. Click the Endpoint Route Table menu.
3. Select the desired route table from the list, and click the [Set routes] button.
4. When the Set route table popup window, set routing rules.
   • Destination: enter the destination's IP address in the form of a CIDR block.
   • Target Type: select the type of the next hop for communication with the destination
     • LOCAL: set communication between transit VPC resources
     • SFC: configure the SFC created through the Service Function Chain menu
   • Target Name: select the next hop to specify within the selected target type
   • [Create]: add the routing rules you entered to the list
5. Click the [OK] button.
6. To check the set rules, select the route table from the Endpoint Route Table list, ,and click the [Routes] tab.

Set related endpoint

To set endpoints to apply the set Endpoint Route Table, follow these steps:

1. From within the VPC environment on the NAVER Cloud Platform console, click Services> Networking> VPC in order.
2. Click the Endpoint Route Table menu.
3. Select the desired route table from the list, and click the [Set related endpoint] button.
4. When the Set related endpoint popup window appears, select an endpoint, and click the [Create] button to add the endpoint.
5. Click the [OK] button.
6. To check the added endpoint, select the route table from the Endpoint Route Table list, ,and click the [Related endpoint] tap.

Delete Endpoint Route Table

To delete the created and operating Endpoint Route Table, follow these steps:

1. From within the VPC environment on the NAVER Cloud Platform console, click Services> Networking> VPC in order.
2. Click the Endpoint Route Table menu.
3. Click the route table you want to delete, and then click the [Delete Endpoint Route Table] button.
4. When the Delete route table popup window appears, click the [Delete] button.